Appointment

 

 

Everyone may have their own opinion when it comes to How to Install a Bathtub Yourself.

Setting up a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult job. If the old tub is conveniently available, the task can move easily; if you have to open up a wall surface to remove the old bathtub and place the new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the job and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will assist you install a brand-new bathtub in your washroom if you have actually currently purchased a brand-new tub and also don't require to alter the arrangement of your previous water system pipelines.
Your tools and also material list ought to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Getting ready for the Installment

First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Bath tub

Utilizing the two wooden boards under its feet, position the tub in the needed position. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the tub up until the spirit level checks out level.
To install taps, fit the bottom of the outermost adaptable tap port to the proper supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water system and also examine all joints as well as new pipework for leaks as well as tighten them if needed. Load the bath tub and also check the overflow outlet as well as the typical electrical outlet for leakages.
Finally, deal with the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub must wait up until the bath tub has actually been made use of a minimum of when as this will certainly resolve it into its final setting.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washers remain in location in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. Once the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bath tub

In the location where the bathroom satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealant can break fairly very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof sticky and cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

As an avid reader on A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that section was a good idea. Remember to take the time to share this content if you enjoyed it. We treasure reading our article about Installing A Bathtub.

Schedule A Free Estimate